Parade

"To us in America, the reflections of Armistice Day will be filled with solemn pride in the heroism of those who died in the country’s service and with gratitude for the victory, both because of the thing from which it has freed us and because of the opportunity it has given America to show her sympathy with peace and justice in the councils of the nations…"  President Woodrow Wilson, November 1919

Thank you to all our Veterans!

Thingamajigger pulled the Cub Scout float in the Veterans Day parade last week. Followed by the Boy Scout Troop, the Thingamajigger supplied smiles, water and Thank You's to the veterans of our community.

Silly stuff that bothers me

Did a little finicky tinkering today.

Why doesn't the yellow light work on the water level indicator when the red and green work fine? Bad connection.

What happened to the sound in my right rear upper speaker? Answer - I disconnected it because it was behind my child's head - time to reconnect.

Test fit the grey water tank. Had no instructions to determine which brackets and bolts go where?  Sure I could figure it out, but why turn a 2 hour job into 4 hours?  Called Bus Depot and they provided a link to pictures.

Tightened up the stove top so it will not rattle like it did.

My mirror in the closet came loose.  Needed to replace the support plastic tabs.

Installed the walkway trim piece I had in my garage.

Silly little stuff - but stuff that bothered me.

Spent some time relocating the summer time junk that was accumulating in the Thingamajigger's garage space. Getting to be that time of year.

Contemplated some pop top work and thought better of it.  No major projects before the Veterans Day parade as I am towing the float for my son's Cub Scout Pack.

Grey water tank

Typical RV's have three types of water storage tanks - 1. Fresh water;  2. Black Water (toilet sewage) 3. Gray Water (sink sewage). While the black water tank is generally not built in to our vans, I felt that the grey water should be.  Have used a bucket in the past, but a nasty spill (and resulting cleanup) this summer got me thinking there had to be a better way.

Most states consider the water that drains from our Vanagons as sewage due to high concentration of solids. So what are the options?

There is the bucket method.  The water drains straight down through piping to empty out under the van into a bucket.  This requires a walk to the latrine, or a proper sewage dump station.  There are tanks that also provide a 'safer' version of transport. Generally wheels are attached. But venting needs to be considered as well.

Also, where do you store the bucket or tank on wheels?

There are collapsible tanks, that can be thrown out when they get too grungy.  But they tend to be too tall to drain directly into, requiring a tubing system to use.

Tanks. 

There are a few options here.  I have seen some on the Samba successfully modifying an older Bay window water tank to mount under the van.  I even bought one to do this, but then thought better of it.  I have also seen some make a tank out of 4 or 6 inch schedule 40 PVC.

Then I saw this little gem.  

 

http://www.busdepot.com/255070814c

 

 

 

 

Bought it with mounting kit. Little bit on pricier side, but it's made especially for this purpose by the factory.  Designed to work around your propane tank, it mounts up under the kitchen with its own mount kit.

 

Once I have a few moments, I will install it and add some pictures.

Bus Depot provided this link for the installation directions.  It is in German, but pictures are worth a thousand words, right?

http://www.vwbusshop.de/WebRoot/Sage/Shops/GuenzlClassicParts/MediaGallery/Anleitungen/Abwassertank_Joker.pdf

Salem Massachusetts

at Halloween!  What a fun time.

Ran around the city taking in the Halloween frights.

Transporterfest was this weekend at the Lars Anderson Museum in Brookline.

Some of the participants found their way to a campground in Salem for some pre-show enjoyment.

Good to see all the usual folk (notice I make no reference to normal), and meet some new VW people.

LP

25 likeminded VW folk.

Lots of laughs, VW stories and such.



Sunrise over the cove at Winter Island

Brake lines

One of my brake lines popped today on way home from NH.

Knew this project was coming - just did not expect the excitement of losing pedal.  Guess the brake kit and new suspension gets mounted this week.

Going to be a long week.

Update - after it stopped raining, and my undercarriage had the night to dry off I had a look at the leak under the van. Turns out I popped a caliper!  Of all the weak lines and points of failure, the last place I expected a problem was the 2 year old rebuilt calipers!

Ordered up a rebuilt one from Bus Depot to get through rest of season and then I will upgrade to new setup with all new lines, booster, et al.

Best use for an IKEA towel rack

Found myself the owner of a towel rack from ikea.  No idea where it came from, it just showed up in my garage.  I was looking at it for a number of months before it hit me - the perfect use for that thing.

Attached it on loft shelf above my sandblast cabinet.  Out of way, but convenient as well.  Holds 12 rolls of varying gauge wire. 

Radiator baffles

In efforts to lower wind noise in the Thingamajigger, I thought I would try to add some OEM equipment into the van to alleviate some possible sources of noise.  The first was the radiator baffles.  I have never had any on the van.  If it were not for the Samba, I would not have know they existed. I don't remember them on earlier vans of mine.

Anyway - bought the Go Westy aftermarket version.  Nice pieces.  Some sort of recycled material.

First step was to remove the upper and lower grilles.  Also, you will need to drop your spare tire clamshell.  

Test fitting the pieces will ensure you understand the fitment before you start.

I started with the left baffle.  Used a stainless carriage bolt, washer and loc nut to hold lower portion in place.  Then adjusted the upper tab to fit in to cross support.  The upper tab is held in place with a push clip.  Mine were still in place from when original baffles deteriorated (or were improperly removed).  These clips need to be carefully pried up and pinched together to remove with out breaking.  

Next, I went for the lower baffle.  Upon looking underneath, I found the mount points on the radiator.

The 'newish' radiator has never had anything attached here.  I had some 1/2 inch 8-32 stainless screws in screw bin.  So I grabbed a tap and a tap handle and put some threads into the radiator mount.

Placing the baffle into place, and using a pair of stainless finishing washers, I secured the baffle into position.

Finally, the right side.  It's similar to the left, but without the same access.  You cannot reach up from underneath to tighten the loc nut.  On this baffle you need to reach in from the radiator side of the baffle to get a 1/4 in drive ratchet to secure the nut on the carriage bolt.  

Cannot really see them here, but they are there.

The other thing I am trying is to replace the functions of the grille air dam pieces that are also missing from my van.  I suppose the better option would be to just cave in and buy the South African grille as the space that I intend to block would already be covered by the secondary lighting.

I grabbed some pieces of lexan I had in my basement.  Cut them into exact opposite pieces for each end of the grill, drilled holes for clearance over the stock location pins. The 'heads' of these need to be carved off.  These were preened over with a hot iron to retain the original blocking baffles.

Once I had my pieces created and modified for clearance, I adhered them to the back of the grille with 5 minute epoxy. 

My only caution I have to state when doing this is to leave enough access to the bleeder screw on top of the radiator.  When I need to bleed the radiator, I never remove the grille as I can reach in with a 13 mm wrench and perform the bleed.  Too much of the new baffle would remove this easy access.

Now I shall go out and try the air flow and noise reduction.

Jersey Shore

Thingamajigger found its way to the Shore this weekend. 

Very late decision to go.  Left at 7pm Friday.  Saw two on the way, and another down there. Passed a two toned early tintop on Rte 84. 

4.5 hours later, we were pulling into Point Pleasant.

Van ran well.  Transaxle was smooth and the shift was like a warm knife through butter.

Many compliments and questions on the van itself.

Medic! Need a medic!

The hike I had with my kid and his Cub Scout friends got me thinking. (Uh oh)

I need a better med kit in the van.  The small generic box was fine for cuts and scrapes, but we are better than that - we are Scouts.  

I have a full Med bag that was graciously donated and will be maintained by a local Ambulance Service.  That does go on most all outings with the Pack. But what if I forget, or what if I have a couple kids who fall?

Needed a better kit.

Bought this kit online: Largest self contained box I can fit into the space I had planned. 

If there was one kit that was one inch smaller in height, it would be perfect. This one barely clears the hatch and I may have issue with curtain movement, but should be ok. 

Since I did not find it perfect - I did not want to perma-mount it, I used some high quality 3M double sided tape. 

Will give it a 6 month test. 

Also in this picture you can see my record system for maintenance and major component replacement. Available in one place, at a glance.  Also have listed my part numbers for preferred plugs, wires, belts and such.  Can't see it when door is closed. 

Works for me. 

Propex

Just plunked down the coin for a Propex HS 2211 heat system from Karl at Westyventures.  He is the importer for these systems and I felt a better choice for purchase than the usual suspects.

With so much work (good thing as I can afford more bits for the van and bad thing because I cannot enjoy it) this year, I have not camped as much as I would have liked to and without adequate camp time, I will be unfulfilled going into the winter season making for an intolerable winter.

With a safe heat system, I will have option to camp much later and continue to wander well into late autumn - early winter.  Once there is snow the Thingamajigger goes away.

http://www.westyventures.com/HS2211%20flyer.pdf

Transaxle

Given the length of time I had to wait on the transaxle, I was able to assemble the bits to do a proper install:

Powerflex bushing from T3 Technique, Swepco 201 lube, new clutch kit, shift linkage rebuild kit from Van Cafe, couple shift rod bushing boots / new shift rod bushing, and a new clutch slave cylinder.

With all the bits in hand, I propped up the van.

Inspecting underneath and I get to thinking (Warning - I suffer from a serious case of "while I am under there syndrome") I think that I should also exchange out my coolant pipes and since it's easier to do it with fuel tank partially dropped, and since I am going to do that I am going to adjust the fuel sender so it reads correctly.

So,with the Thingamajigger propped up at door to garage ( garage is too short to fit van in and jack it up the height I need), I started draining fluids.

Cleaned the floor of any debris that will catch the creeper, and then decided to put a half sheet of plywood there to aid movement.

After fluids were drained (coolant and fuel), I got to disassembling the transaxle from the engine.  With the Zetec setup, it is imperative to support the motor.  I used a custom cut piece of 5x5 PT that I have used before.  Was nice to find it again as usually my kid takes that sort of thing and 'creates' stuff.

Removed the shift shaft and mechanism (marking the placement of the shaft versus the clamp), removed the starter, removed the bolts for the CV joints, disconnected the clutch slave cylinder and then supported the tranny while I removed the three remaining nuts that hold the transaxle to the motor.  Then (with tranny supported) I removed the front transaxle mount bolts and ground strap from the body.

Carefully lower the transaxle a bit (too much and it binds - or worse, bends the studs the transaxle mounts upon).  Now you can start to wrestle the transaxle away from the motor.  Pull a bit, lower a bit, pull a bit and lower enough to clear trans mount.  Slid right off.  

The plywood came in handy to slide the old transaxle out easily.

Now with transaxle out, I slid under and assessed the rest of the plan.  I was able to sit up under the transaxle cavity and tear out the ancient matting that was still in a solid form, but the foam part was wet and it had not rained in a couple weeks.  Good thing the plastic backing was in tact as the metal behind it would have been rotted to hell if it was not.

With that gone, it brightened up the work area.

Made sense to drop the tank now.  Dropped the rearward side enough to spin out the sender and corrected the angle of the float (a best guess).

Then I got to pulling the coolant lines.  My coolant lines were really not that bad, as I know they were replaced about 13 or 14 years ago by prior owner Bill.  But my precautionary side got the best of me a few months back and I bought the stainless steel coolant pipes on sale from Rocky Mountain Westy.

Having them in the garage, and transmission out, it just made sense.  I was not trying to save the pipes for any reason, so I cut them in two pieces each and removed them.

Was a fairly straight forward installation.  I made sure to notice the bends in the old one and their position relative to the new ones and marked them with a sharpie. 

Within 30 minutes I had the new ones installed.  I used some rubber from a coolant hose to surround the SS pipes anywhere they may contact with body metal (abrasion resistance) and since I did not have a rear mount for the pipes, I fashioned one from some SS strapping and a piece of 1/2 inch fuel line slid over.  This I bent to appropriate position and used factory mount holes to support the rear portion of the pipes.  Also since I had all the coolant out, I also took the opportunity to re route the heater lines and tightened them up to the bottom of the body. Everything is close, tight and beautiful.

I though I took a picture, but I will have to get back under and take another.

Next was to prep the transmission for installation.  The older mounts had to be removed off the old transaxle and all the periphery stuff as well.  The front mount needed to be further broken down to remove the metal sleeved rubber mount.  No matter what configuration I tried, I could not get it to work in the press.  

Went old school - hammer, chisel and a vice.  Drilled through the rubber in order to provide clearance to thread a hack saw blade through.  I cut through the outer metal sleeve in two places to relieve the outward pressure and hammered the bushing right out with chisel.

I pulled it all, cleaned up with degreaser and did them up in the sandblaster.

In the picture you will see the clutch slave cylinder mount, the clutch actuator arm, the front transaxle mount (two pieces).  

While those dried, I started disassembling the shifter linkage arm.  Removed the pin that hold the lever arm on the shaft and then removed the lever itself.  This needs to come off in order to replace the bushing.

Here you can see the condition of the bushing and the housing.

These pieces got degreased and then popped into the sandblaster.  Painted and set to dry, my transmission mounts were dry to touch.  I built the transmission mount with the new Powerflex bushing and attached it to transaxle.  Slid the clutch slave cylinder brackets on the transaxle and then the actuator lever with its circlip.

I found the rearward slave cylinder support bracket on ground so I needed to repaint it, so it's not in this picture.  But you can also see the rebuilt shifter arm in the foreground.  

Here it is again with some chrome button head bolts as I could not find the stainless ones I bought and I do not consider it an issue here. Painted that as well, although in New England this sort of thing does not last long. Even powder coating does not last long - one chip and the water gets in and it rusts underneath. C'est la vie. 

So now that I had the new clutch installed and new support bearing, it was time to install the transaxle.  Remember to fill your transaxle prior to installation, it's just easier.  Current VW board suggestions are to use the Swepco 201 for applications under 150hp, and Swepco 210 for over 150 hp. There are huge debates over this no matter what vehicle forum you peruse, I went with what Rancho suggested.  

Slid it under on my creeper and rolled it off.  Got it lifted into place with assistance of a floor jack and got it up there with some more wrestling around.  

Installed transaxle, time to reinstall the starter, shift linkage, new slave cylinder, all the mounts, CV joints, Zetec specific speed sensor, ground strap, etc.

In this photo you can see the next project - resealing the HC oil pan.  Will do when I perform next oil change. I was also grabbing tools to connect the CV joints here, and grease to repack the joint.

Transaxle installed, connectors all checked for proper torque, I went to cooling system and checked all those connectors and clamps, then reinstalled my fuel tank.  Time to check for leaks. 

Filled with coolant and refilled my fuel.  Fired right up and shifter worked, but was finicky.  Assumed that due to my 'new' parts, I would need to play around with adjustment. Took me a half dozen tries to get it where I was somewhat pleased.  Still think it needs additional adjustment. Will use a bit and correct after break in period.

Cub Scouts

Rocked the Thingamajigger for a Cub Scout hike this morning.

Today's adventure

Started at a Limbo members house. A number of VW folks gathered there last night for a night of fun prior to today's Volks Fair in Shrewsbury MA.

Even a few Vanagons on a trailer destined for Virginia based collector who has over 400.

Headed over to show site. Helped do some set up and watched the cars roll in

This white 67 was my favorite of the show.

Then it was time for some fun with my kid

Bought him a kayak last year, just gave it to him today as I felt his swimming skills were good now.  He took to the kayak immediately and was paddling quite well.  Slid the kayaks back into the van (on a tarp) and headed for home.

Good day in the VW.

Transaxle story

So I ordered a rebuilt transaxle from Rancho.  They were three weeks behind they said, but that was fine as I have been busy otherwise.  That was on the 17th of June.

Called on the 14th of July and was told it was going out that week, 'was in build station now'.

Called back yesterday the 29th, and 'it's in the build station now'. Questioned the earlier comment along the same lines? Reply was that they would have it out, at latest the following day.

Charge card alert came through my phone text today - 6 weeks later.  Should be across the country by early next week.  Thinking that it would have been best if I had ordered it as soon as I suspected a problem.

On the plus side - Gave me time to assemble the other parts necessary for the installation: A Powerflex trans mount bushing, a new shift guide bushing, new shifter parts, a couple new cv joint boots, and all the brake lines and such while I am provided with ample access to the body behind the transaxle.

UPDATE:  It arrived!  On 5 August it arrived at my home.  UPS left it on my back porch per Rancho despite requesting it to be shipped to a friends body shop.  Weighs in at 95 pounds boxed, just as much as my wife (unboxed) - she had a hell of a time moving it until I got home late last night.

Mohawk Trail

Enjoyed the van this weekend instead of tinkering.

Went to pick up my kid at Camp Mujigae - Korean Culture camp in Albany.  On way back we camped in Western Massachusetts.

Setting up camp.
 

 

 

Actually, I set up camp - he plays.

And plays

And plays some more. 

 

Then he built us a fire, and we ate dinner.  Made s'mores. Have taught him well, little bugger knows how to perfectly caramelize a marshmallow.

Following morning, after fishing for a bit and then some breakfast, we drove up Mount Greylock. At 3491 feet, it is the tallest peak in Massachusetts. 

So after taking this picture I threw up my hands and ran flailing my arms singing "The hills are alive with the sound of music".  A few of the older folks got a laugh out of it.  My son wouldn't speak to me for a few minutes - I had embarrassed him.  I tell him it's my job, just wait until prom and I am a chaperone!

Drove home along the Mohawk trail.

Have a second job lined up for the winter:

Pop top completion (sort of)

Got the tent done today.

It went smoothly, I guess, for a humid and 90 degree day in a pop top.  Think I will need to wash those cushions from all my sweat. Yuck.

The next step was to try the fitment on the Wasserstopper.  It took some doing, and I cannot foresee how happy I will be if I need to do that in the rain.  Also - the van sits too high for me to reach up to the extension snaps without a step up.  That makes me nervous.

Ok it fits, but I still have some reservations.  We shall see the first time I go to use it.  I do like that the clips on the passenger side attach to the awning case thereby eliminating the drip line from the roof, behind the awning and onto everything I attempt to keep dry in the first place.

Final touch was the new Westfalia sticker.  It looked wrong to me when I was gazing at it.  Could not figure out why.

Then after grabbing a celebratory tasty beverage, I figured it out.

The Westfalia sticker that was on there prior was brown.  I went with black on this round due to the changes taking place in and out of the van, but had forgotten as the parts have been in the garage for months.

Now I only need that flat pop top gasket that has been back ordered.  May need to reuse my 2 year old one so I can camp this weekend.

There will be a rain delay for this game

Despite the ominous sky, I got some things done.

Luggage rack is rebuilt and reinstalled.  New gasket and new stainless hardware. :)

I should make note that I cleaned up the roof under the luggage rack, applied a coat of wax and polished it.  The. Thought again and applied another coat of wax and left it.  After seeing all the stuff under there, I thought it prudent. 

I also installed a set of screens under the holes on the luggage rack.  Took some of my screen material from the basement, cut 5 patches and epoxied them onto the bottom of the hole. No more bugs, pine needles, maple tree 'helicopters' or other debris collecting under there.

Reinstalled the pop top vent.  New seal, stainless hardware and stainless hinges.  Should be no need to remove this again.

Got the roof on as it was starting to sprinkle.  

With the thunderstorm warnings going all afternoon, I thought I had achieved all that I could.  So why not celebrate a good job and have a tasty beverage?

Despite the warnings, I forged on in the sprinkle until I started to see lightning. Got all the new hardware in and the top lined up to close just right.

Started playing with the new tent.

I took a due from the original and tack stapled the new tent in all around with evenly spaced staples.  This allowed me to see if my tent install is correctly placed, centered and ready to move to next step.

At this time the thunder crash and lightning was becoming close.  So rather than deal with overly wet situation, I chose to put her away in the garage for the night.

Now for the next tasty beverage.